Spinning Reel Drag Not Working

1. Quick Fix Instructions– Spinning Reels Super Stopper Roller.
2. Baitcaster Drag Not Working | A Day's Catch.
3. 10 Most Common Reel Performance Problems - Game & Fish.
4. What Is Drag on a Fishing Reel? [In Depth] | Pursuing Outdoors.
5. Zebco 33 Drag Not Working - Fishing Talks.
6. This Is Why Your Spinning Reel Drag Isn't Clicking - YouTube.
7. Drag quits working on my ice fishing reels.
8. Baitcaster Drag Not Working Properly- How To Fix? - FishingMet.
9. How To Maintain The Drag On A Spinning Reel - Cadence.
10. Common Spinning Reel Problems (And How To Fix Them).
11. Reel drag not working properly - FishingMagic Magazine.
12. Drag won't tighten sufficiently - Fishing Rods, Reels, Line,.
13. Lew's - Another great question regarding drag failure when.
14. How to Repair the Drag System on a Spincast Reel | Gone.

Quick Fix Instructions– Spinning Reels Super Stopper Roller.

Drag knob counter-clockwise. Remove spool washers and spool sup-port by pulling them upward towards the end of the spool shaft. Remove the small retaining screw with a small screwdriver. Then use a 1/2 inch nut driver, deep socket, or crescent wrench to remove rotor nut. Roller Clutch Assembly. Step 1. First off, use the screwdriver to loosen and remove the little screw which holds the bail wire in place. Remove the one on the side of the pivoting arm. Depending on the model of spinning reel you have, you might also have to remove the screw on the opposite side. My reel drag isnt working as it should, i have to really loosen it up for it to work when i get a fish on but then when i real in it just spinning like crazy and i cant get much line on the spool but as soon as i tighten it up it just wont drag.

Baitcaster Drag Not Working | A Day's Catch.

Step by step instructions to overhaul your fishing reel's drag system for smoother performance.Instruction shown in 1080p-HD.

10 Most Common Reel Performance Problems - Game & Fish.

You have to readjust your drag. Some higher end reels will allow your drag to stay adjusted even when removing the knob, however, quite honestly, if you have one of those reels, you probably do not need to come here asking questions about, since they are higher end professional reels.

What Is Drag on a Fishing Reel? [In Depth] | Pursuing Outdoors.

2: Bail Spring The internal bail spring is usually the main cause of mechanical failure we usually experience with our spinning reel, this results in the return spring failing to flip the bail back open. Usually, wear and tear are the main cause or.

Zebco 33 Drag Not Working - Fishing Talks.

509. Location Oregon. My PB: Between 6-7 lbs. Favorite Bass: Smallmouth. Favorite Lake or River Columbia River. Share. Posted April 9, 2015. I recently cleaned, re-oiled and re-greased, and reassembled my Lew's Laser RZ reel and now the drag is really slipping. On absolute max drag, it doesn't take a lot of force to turn the handle any more..

This Is Why Your Spinning Reel Drag Isn't Clicking - YouTube.

If the felt is still serviceable, brush the discs with a soft bristle brush and apply a good reel cleaning solvent like Reelx to remove any caked-on grit (no WD-40!). Gently work the solution into the felt with your fingers. Once done, grab a soft. How to maintain the drag in your spinning reel. This is an often overlooked piece of maintenance when it comes to fishing reels. A sticky drag can lead to lo.

Drag quits working on my ice fishing reels.

The drag, or the drag system, typically involves a pair of small steel plates that are located inside the reel. They are used to put pressure on the spool and stop it from releasing more line. This system enables you to pull heavy fish without breaking the line. The drag power is the amount of pressure that the plates put on the spool. A common reason for baitcaster drag is if your rod’s reel is not correctly adjusted. Make sure the drag is set to a level that will allow you to control the force of the drag without too much resistance. For instance, if you have a 10lbs drag setting, don’t use it with a smaller fish. A smaller fish will only break the line and get away.

Baitcaster Drag Not Working Properly- How To Fix? - FishingMet.

. A quick test to see if your drag is working is to put a small mark on the rim of your spool with a marker. Tighten your drag all the way down. Place your thumb firmly on top of your line and crank the reel handle. If the mark turns and the line does not turn with the same rotation, the drag is working properly and the line is slipping on the spool. Just looking for a little help to get the drag working. When I loosen the drag all the way and pull on the line nothing happens it’s just stuck. I was hoping Someone can help me out. I believe I have a 1970’s zebco 33. The issue is the drag doesn’t work. The spool is locked down tight not sure if it’s supposed to spin or if washers are.

How To Maintain The Drag On A Spinning Reel - Cadence.

If you did not use mono backing or some tape on the reel spool arbor before installing the braid, you are getting "ghost drag". Ghost Drag is the slipping of the spooled line on the spool arbor which is common with braids because the braids don't have enough friction on metal to keep it from happening. Even though you may not have experienced it right after. Step Three. Most reels have a series of washers in the drag system. It’s important that you keep them in the proper order. Either remove them one at a time and lay them out in order, or remove them all together in a stack and clean them one at a time. Use a paper towel to remove any dirt and moisture, then clean out the spool with a cotton swab.

Common Spinning Reel Problems (And How To Fix Them).

The fix is to put more waves in it. Use a long nose pliers to bend it. I put around 5 more bends in it. But don't go overboard, otherwise it'll be a real "drag" (too much drag). If you put too much bend in the washer, you can use the long nose to flatten it a bit. Put it all back together the same way you took it apart. Hold your rod at a 45-degree angle and hook the weight. For best results, the drag setting should be able at the point where the line holds a third to half of its weight before moving (e.g., a 20-pound line should not move until the hook holds seven to ten pounds). It’s better to have your drag too loose and fight a fish a little longer than. Even if the problem does not get so bad, corrosion is a common cause of baitcaster drag not working. You will have to replace the reel if there is too much damage. Use a toothbrush to clean the level wind. After fishing in saltwater, do not forget to rinse the reels. Over Lubrication Not lubricating the reel is bad, but over-lubricating is also.

Reel drag not working properly - FishingMagic Magazine.

There might be several reasons behind why your spinning reel is going both ways. But most of the time, the answer is ‘spinning reel anti-reverse is not working.’ And if that is not the case, then there might be some problem with the drag. The simplest solution of it is to engage the anti-reverse button. It should work properly after that. A common problem with spinning reels is a frozen drag, which is often caused by dirt, debris, or the drag being left tightened. Always loosen your drag completely after using your spinning reel. If loosening the drag and turning the spool frees the drag, then there is usually no need for disassembly. Simply tighten the drag tension knob to test it. Is your spinning reel drag silent?This is a common problem that anglers run into and in this video, I'm going to show you how to identify the root cause of i.

Drag won't tighten sufficiently - Fishing Rods, Reels, Line,.

Hey guys just wondering if you got and tips or tricks to keeping the drag from not working on your ice fishing reels. It seems every reel I buy thats the reason I end up having to buy new reels.... Drag quits working on my ice fishing reels. SUBSCRIBE SUBSCRIBE ADD TO FAV ORTIES. 12/16/13 @ 2:15 PM. ORIGINAL POST. Largeshinner. USER SINCE 1/14/09. The lubrication on the clutch washers will cause the drag clutch to not work properly at low temperatures. The lub that comes in the reel clutch is designed to work at high temperature because of the heat build up when the drag slips. Washing out the drag with a stoddard chemical such as WD40 should help the problem during cold weather.

Lew's - Another great question regarding drag failure when.

If the drag clicks and the spool spins, then this is not the issue. But if line comes off of your reel and the spool does not spin, then it likely is the issue. To fix this, put some mono backing on your reel. Reason #2: The gear. Added new braid to my spinning reel and today I realized my drag was not working after tightening it down all the way. When I pulled on the line it Press J to jump to the feed. Press question mark to learn the rest of the keyboard shortcuts. Search within r/FishingForBeginners. r/FishingForBeginners. Log In Sign Up. User account menu. Found the internet! 2. Spinning reel.

How to Repair the Drag System on a Spincast Reel | Gone.

How to Repair the Drag System on a Spincast Reel. By Eric Cedric. Fishing reels are made to cast out line and retrieve via the spool and handle. Many modern fishing reels use anti-reverse clutches or mechanisms that allow the reel to spin both ways.... Start the repair by checking the most obvious fixes first, and if those do not work, go to. Fact is that the drag still has a pretty good range but has a lighter startup in light drag settings. The greased drag in these multi disk reels works very similar to a non greased setup other than the extreme top end (max drag pressure). The maximum drag tension is lessened to a degree with the grease.